This is a schematic diagram of video amplifier circuit with bi-phase output. Bi-phase output provides both positive-going and negative-going signal, and can be used as balanced signaling. The main component of this circuit is LM1201. In this circuit, the inverted video is obtained at pin 10 because of the 75Ω termination to the power supply voltage. The voltage divider on pin 6 is used to set the black level on inverted video (pin 8) to 1.5V. Here is the schematic diagram of the circuit:
obtained at pin 10 because of the 75Ω termination to the power
supply voltage. The voltage divider on pin 6 is used to set the
Black level on inverted video(pin 8) to 1.5V. Here is the circuit:This is a Video Amplifier circuit with Bi-Phase Output. The main
component of this circuit is LM1201. The inverted video can be
obtained at pin 10 because of the 75Ω termination to the power
supply voltage. The voltage divider on pin 6 is used to set the
Black level on inverted video(pin 8) to 1.5V. Here is the circuit:This is a Video Amplifier circuit with Bi-Phase Output. The main
component of this circuit is LM1201. The inverted video can be
obtained at pin 10 because of the 75Ω termination to the power
supply voltage. The voltage divider on pin 6 is used to set the
Black level on inverted video(pin 8) to 1.5V. Here is the circuit:This is a Video Amplifier circuit with Bi-Phase Output. The main
component of this circuit is LM1201. The inverted video can be
obtained at pin 10 because of the 75Ω termination to the power
supply voltage. The voltage divider on pin 6 is used to set the
Black level on inverted video(pin 8) to 1.5V. Here is the circuit:
Possibly Related Articles:
- Balanced Input Microphone Pre-Amplifier, High Quality Audio For Long Distance Wiring
Balanced input has three connections, ground, positive signal, and negative signal. When we trace the signal using oscilloscope, if we take the ground as the reference, then the negative signal... - FET Cascode Video Amplifier
This is a simple FET Cascode Video Amplifier circuit. This circuit has some features, they are reduction of feedback to almost zero and very low input loading. Here is the... - Voltage Controlled Variable Gain Video Amplifier
This is a video amplifier circuit featured with controllable variable gain. The control is done by adjusting the voltage of grid inputs of two FETs, which are configured as programmable... - Enabling 3 Phase Motor to Operates with Single Phase Supply
Capacitor have been use for decades to operate 3-phase motors on single-phase power. Two single-phase wires are connected to two of the inputs on a 3 phase motor on this... - 3 Phase to Single Phase Rotary Converter
In the circuit the rotary converter is nothing more than a second motor which is acting as a generator. The tools motor performed this function with the static converter, but... - Video Wire: Enable Video Transmission Via Long Cables
This circuit enables you to connect your camera with very long wire. The circuit is actually a video amplifiers. At the sender part, the amplifier is used to make a... - Fast Amplifier Circuit with DC Stabilization
This amplifier circuit combines the LT1010 and a fast discrete stage with an LT1008 based dc stabilizing loop. A differential stage which is single-ends into the LT1010 is formed by... - High Impedance Low Capacitance Buffer/Amplifier
These are circuits of high impedance low capacitance buffer and high impedance low capacitance amplifier. First figure is a high impedance low capacitance buffer circuit, it uses the 2N446 JFET... - Higher Output Current for Op-Amp
Almost all monolithic amplifiers have good loaded output voltage swings, delivering +-10V at 5 mA with +-15V supplies because they use class-B output stages. It would be require much more... - 2 Phase and 3 Phase Motor Drivers
The schematic diagram below show 2-phase and 3-phase motor driver circuits. This circuit can used to drive an AC motor because this circuit has an integrated power operational amplifier, built-in... - Multi Output Power Supply
This transformer-rectifier-filter arrangement gives you multiple output voltages with a single transformer. This AC-DC converter can be your solution is you need two level of symmetric power supply. Here is... - LM359 Phase Locked Loop
Phase-locked loop is very common in telecommunication, control, and other electronic application. PLL can be used to demodulate FM signal, produce a stable clock signal, or to recover a synchronization...
| 
